日韩乱码人妻无码中文字幕,玩弄放荡人妻少妇系列视频,久久久久久亚洲精品无码,国产黄A三级三级三级看三级

管道空氣彈簧的運行步驟:

Operation steps of pipeline air spring:

橡膠空氣彈簧的用途很廣泛相信大家都有熟悉？那么，本期我們就來來看一下子管道空氣彈簧的運用步驟。

Rubber air springs are used in a variety of ways that I'm sure you're all familiar with, right?So, in this issue we will look at all of a sudden the use of air spring pipeline steps.

1、運用前：先將管道空氣彈簧與充氣裝備配件進行聯接，做一下子漏氣測試。將充完氣的管道空氣彈簧放入到盛滿水的水盆中并按住，同自行驗車檢查驗看看測定車帶漏氣一個道理，看是否有氣泡兒，沒有氣泡兒即可運用，如有氣泡兒就是有漏氣現象需求修補一下子。

1. Before application: connect the pipe air spring with the inflatable equipment accessories, and do the air leakage test all at once.Will be filled with air into the pipe air spring filled with water in the basin and hold, with a car check check check to determine the car belt leakage a reason, see whether there is a bubble son, no bubble son can be used, if there is a bubble son is a leak phenomenon need to repair a while.

2、運用時：將管道空氣彈簧絕對送入管道內，如需重要的職位員下去操縱，一定要安裝法蘭，保證職員安全，把管道空氣彈簧的氣嘴那一頭用管子、壓力計、風泵等充氣工具聯接好，之后依照壓力計上的刻度來充氣。充氣時，假設管道空氣彈簧向一側膨脹，大氣的壓力打不上去，此時假設再繼承充氣的話會把氣囊打爆。這時要檢查管道內的淤沙是否徹底收拾干凈，內壁一定要平整，不應該有毛刺，否則會刺破氣囊。

2, when the use: the pipe air spring is absolutely into the pipe, such as the need for an important position to operate, be sure to install the flange, ensure the safety of staff, the pipe air spring at the end of the air nozzle with pipe, pressure gauge, air pump and other inflatable tools connected, then according to the scale on the pressure gauge to inflate.When inflating, it is assumed that the air spring in the pipe expands to one side, and the atmospheric pressure cannot be exerted. At this time, it is assumed that if the air is inflated again, the air bag will explode.At this time to check the pipe silt is thoroughly cleaned, the inner wall must be smooth, should not have burrs, otherwise it will puncture the air bag.

3、運用后：將管道空氣彈簧的閥門掀開，慢慢放氣，之后垂直抽出管道空氣彈簧，注意不要被附近的東西刺破管道空氣彈簧，影響下次運用。

3. After use: lift the valve of the air spring in the pipeline, slowly release the air, and then vertically extract the air spring in the pipeline. Pay attention not to be pierced by something nearby, which will affect the next use.